版权声明:本文首发自企业旺旺,请随意转发,本文编辑字数3315字,预计阅读时间,2分钟。3分钟前更新:欢迎前来南昌企业旺旺了解南昌路易瑞国际贸易有限公司发布的南昌热镀锌方管天津路易瑞国际有价格,南昌热镀锌方管天津路易瑞国际有厂家信息,26服务质量好,性价比高,为您节省采购成本!
基本参数
- 材质
Q235,Q355,Q345,20
- 分类
镀锌方管
- 分类
直角方管
- 分类
无缝方管
- 分类
方通
天津路易瑞Q355B方管改拔规格如下
120×120×4.0~8.0
50×80×2.0~5.0
600×200×10~28.0
50×100×2.0~8.0
600×400×10~28.0
200×200×6.0~12.0
80×100×2.0~8.0
800×400×10~28.0
120×60×2.5~10.0
800×600×10~28.0
250×250×6.0~14.0
120×80×2.5~10.0
280×280×6.0~15.0
150×100×2.5~12.0
300×3500×10~28.0
200×100×00×8.0~14.0
180×150×2.5~12.0
1000×4~12.0
350×350×8.0~14.0
200×150×4~12.0
1000×800×10~28硬度过髙对中碳钢而言,多为退火时加热温度过高,冷巧度太快,或等温温度过低等;另外错误采用了正火处理;对于方管进行球化退火时,欠热或过热均会造成退火后硬度高的缺?或者因冷却速度过快,等温温度过低或时间不足等。补救措 施:重新进行正火处理,如果组织合格,仅硬度高,则可进行一次 高温回火处理。(2) For medium carbon steel, excessive hardness is mainly due to excessive heating temperature, too fast cooling, or too low isothermal temperature during annealing; in addition, incorrect normalizing treatment is used;
厂家分享方管退火与正火的缺陷及补救措施?
方管价格稳中震荡趋稳出货为主厂家分享方管退火与正火的缺陷及补救措施?
①细晶粒断口、低塑性,多发生于冷加工后的Q355B方管。原因在结晶退火或正火时,加热温度偏低或保温时间短,致使冷加工么过程中的破碎晶粒未能全部再结晶造成的。补救措施为:进行?f 晶退火,或进行一次完全退火或正火处理。(1) Fine grain fracture and low plasticity occur mostly in Q355B square tube after cold working. The reason is that during crystallization annealing or normalizing, the heating temperature is low or the holding time is short, which results in the failure of recrystallization of the broken grains in the process of cold working. The remedial measures are as follows: annealing f crystal, or a complete annealing or normalizing treatment.
方管另改拔规格如下
20×50×1.0~2.0
400×250×8~12.0
38×38×1.0~4.0
550×550×10.0~40.0
22×35×0.9~2.0
400×300×8~12.0
40×40×1.0~4.5
600×600×10.0~40.0
700×700×10.0~40.0
25×65×1.0~2.0
450×250×8~12.0
45×45×1.0~5.0
30×40×1.0~3.75
400×300×8~12.0
50×50×1.0~5.0
30×45×1.0~3.75
400×350×8~12.0
60×60×1.5~5.0
30×50×1.0~4.0
70×70×2.0~6.0
30×60×1.0~4.5